Rose electronics Translator Instruction Manual

Browse online or download Instruction Manual for KVM switches Rose electronics Translator. Rose electronics Translator Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1

10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099 WWW.ROSE.COM TM INSTALLATION AND OPERATIONS MANUAL

Page 2 - LIMITED WARRANTY

CABLES SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 6 Cables (See Appendix B for cable part numbers) ServeView Pro to KVM station cables The KVM

Page 3

KEYBOARD COMMANDS SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 7 Table 3 shows the keyboard commands that are available for the ServeView Pro.

Page 4 - TABLE OF CONTENTS

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 8 Table 4 shows the available mode values for the keyboards and mice that are supported. To change

Page 5 - Introduction

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 9 Keyboard command usage When using keyboard commands to enter information to the ServeView Pro, pl

Page 6 - Compatibility

INSTALLATION SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 10 Organizing the system It is recommended that before any ServeView Pro configuration

Page 7 - System overview

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 11 The green POWER LED will turn on and the power-on diagnostic will run. Wait until the SELECT 1

Page 8 - ServeView Pro models

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 12 When all needed CPU ports have been pre-configured, the computers can be connected. Perform the

Page 9 - ServeView Pro models (rear)

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 13 Installation – Cascading units The ServeView Pro units can be cascaded together to expand the nu

Page 10 - CABLES

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 14 Connecting “Slave” units To properly install the Slave units, follow the below steps. Step: (Ref

Page 11 - KEYBOARD COMMANDS

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 15 a. Select the correct keyboard type, if needed, from Table 4. b. Issue the “Set mode” command.

Page 12

LIMITED WARRANTY Copyright  Rose Electronics 1990-2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,

Page 13 - Keyboard command usage

OPERATION SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 16 Selecting a computer To connect to a computer, you can select it from the ServeView Pr

Page 14 - Installation – Single unit

SERIAL PORT SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 17 Serial Port (RS232) The RS232 serial port on the ServeView Pro’s rear panel is used

Page 15 - Connecting the computers

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 18 3. Send the file to the unit using a simple ASCII text file protocol. While the file is being

Page 16

TROUBLESHOOTING SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 19 TROUBLESHOOTING Computer does not boot, keyboard or mouse error received. ¾ Cab

Page 17

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 20 PS/2 mouse gets out of sync ¾ Cabling was disturbed during mouse movement. Issue the null comma

Page 18 - Connecting “Slave” units

SERVICE INFORMATION SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 21 Service Information Maintenance and Repair This Unit does not contain any in

Page 19

SAFETY SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 22 Safety This ServeView Pro KVM switch has been tested for conformance to safety regulation

Page 20 - OPERATION

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 23 Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the

Page 21 - SERIAL PORT

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 24 Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est

Page 22

APPENDICES SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 25 Appendix A. Initial factory settings Setting Default value KVM keyboard/mouse type

Page 23 - TROUBLESHOOTING

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY . FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS T

Page 24

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 26 Appendix B. Parts and cables Part number Description CAB-CX0606Mnnn* Coax VGA-PS/2 Kbd-PS/2 m

Page 25 - SERVICE INFORMATION

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 27 Appendix C. General Specifications The ServeView Pro part number is Sxy-zUB Where x = platform,

Page 26 - SAFETY

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 28 Appendix D. Rack mount instructions The ServeView Pro can be mounted in a rack using the Rackmou

Page 27

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 29 Appendix F. Keyboard mapping KEYBOARD MAPPING FROM PC TO APPLE AND SUN COMPUTERS PC 101

Page 28

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 30 Appendix G. Video distance capability The table below shows the distances, resolution, and quali

Page 30

10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099 WWW.ROSE.COM

Page 31

TABLE OF CONTENTS Contents Disclaimer ...1

Page 32

INTRODUCTION SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual,

Page 33

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 2 Features nn Access up to 256 computers from one KVM station nn Available in three different c

Page 34

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 3 Package contents The package contents consists of the following: nn The ServeView Pro unit nn

Page 35

MODELS SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 4 ServeView Pro models “M” Chassis “B” Chassis “C” Chassis Figure 1. ServeView Pro mode

Page 36

SERVEVIEW PRO INSTALLATION AND OPERATIONS MANUAL 5 ServeView Pro models (rear) “M” Chassis “B” Chassis “C” Chassis Figure 2. Rear panel Label

Comments to this Manuals

No comments