Rose electronics Ultraview Pro KVM SWITCH WITH ON-SCREEN DISPLAY Instruction Manual

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 4 CPU connection All CPU connectors on the UltraView Pro are DB25F. The CPUs are connected to the U

MODELS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 5 UltraView Pro models “M” chassis “B” chassis “C” chassis Figure 1. UltraView model

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 6 UltraView Pro models (rear) “M” Chassis “B” Chassis “C” Chassis Figure 2. Rear Panel Label

CABLES ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 7 UltraView Pro Cables (See Appendix C for cable part numbers) UltraView Pro to KVM station

INSTALLATION ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 8 Organizing the system It is recommended that before any UltraView Pro configuration

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 9 The green POWER LED will turn on and the power-on diagnostic message will display on the KVM moni

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 10 (4 CPUs can be connected using a 4-port unit, 16 using a 16-port unit) Figure 3. UltraView Pro

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 11 (4 units can be cascaded using a 4-port master, 16 using a16-port master) Figure 4. Cascading

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 12 8. Next, select “Expansion width” from the configure system menu and press enter. Enter the nu

CONFIGURATION MENUS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 13 Main configuration menu Figure 5. Main configuration menu The UltraView

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 14 Configure system menu Figure 6. Configure system menu By selecting “SYSTEM” from the main menu

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 15 Expansion If your system consists of cascaded units, the expansion section of the Configure Syst

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 16 Scan time (seconds) To change the scan time, highlight “Scan time” and press enter. An input bo

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 17 Delay This setting is for PC keyboards only. It is used to adjust how long, after a key is depr

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 18 Configure computer menu Figure 7. Configure computer menu The “Configure computer” menu allo

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 19 Keyboard To change a computers keyboard and/or mouse, use the up/down arrow keys to select (high

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 20 Configure overlay Figure 8. Configure overlay menu The “Configure overlay” menu is used to conf

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 21 Resolution Use this configuration to set the resolution for the KVM stations video if no compute

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 22 Configure overlay - Computer select window The “Computer select window” section allows you to ch

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 23 Background color To change the background color, select “Background color” and press enter. A c

LIMITED WARRANTY Copyright  Rose Electronics 1990-2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 24 Font This item sets the font type for the computer label. To change the font, select “Font” and

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 25 Configuration password To assign a “Configuration password”, select it from the “Configure secur

OPERATION ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 26 Selecting a computer To connect to a computer, you can select it from the UltraView Pr

KEYBOARD COMMANDS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 27 Keyboard commands The following table describes the available keyboard command

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 28 Mode value Description M1 CPU keyboard = PC mode 1 (Some IBMs & PS/1’s) M2 CPU keybo

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 29 Keyboard command usage When using keyboard commands to enter information to the UltraView Pro, p

RS232 PORT ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 30 Serial Port (RS232) The RS232 serial port on the UltraView Pro’s rear panel is used f

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 31 To update the UltraView Pro’s firmware, first download the latest revision from Rose Electronics

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 32 If any of these errors occur, check the RS232 cable, the connectors, and the adapter. Make sure

TROUBLESHOOTING ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 33 TROUBLESHOOTING Computer does not boot, keyboard or mouse error received. ¾ Cable

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS This

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 34 Mouse does not move ¾ Mouse not configured. ¾ UltraView Pro turned off after or not connected wh

SERVICE AND MAINTENANCE ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 35 Service Information Maintenance and Repair This Unit does not contain a

SAFETY ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 36 Safety This UltraView Pro KVM switch has been tested for conformance to safety regulatio

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 37 Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 38 Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est

APPENDICES ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 39 Appendix A. Initial factory settings Setting Default value KVM keyboard/mouse type

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 40 Appendix B. Parts and cables Part number Description CAB-CX0606Mnnn** Coax VGA-PS/2 Kbd-PS/2

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 41 Appendix C. General Specifications The UltraView Pro part number is Uxy-zUB Where x = platform,

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 42 Appendix D. Rack mount instructions The UltraView Pro can be mounted in a rack using the Rackmo

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 43 Appendix E. Rack mount illustration Appendix F. Keyboard mapping Sun / Apple keyboard

TABLE OF CONTENTS Contents Disclaimer ...1 Introduction / System ov

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 44 Appendix G. Video distance capability The table below shows the distances, resolution, and qual

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.COM

Figures Figure 1. UltraView models... 5 Figure 2. Rear Panel ...

INTRODUCTION ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual,

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 2 All UltraView Pro models can easily be expanded by chaining the units together and configuring th

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 3 Compatibility Computers Industry standard PCs, Sun, Unix computers such as RS/6000, HP, SGI, DEC